Batca Omega 2 Multi Station (OM-2)

The Batca Omega 2 Multi-Gym is a two-stack commercial multi-station built for facilities that need to train two members at once without giving up the quality of a single-user selectorized machine.

Two independent 200-lb weight stacks let a 220-lb lifter work shoulders while a 130-lb lifter works legs on the opposite side, with no waiting and no compromise on feel. Single-station architecture keeps every pulley, cam, and press arm anchored to one welded frame, so the path of motion stays consistent under heavy load.

Built on 11-gauge structural steel with sealed-bearing pivots and 2,000-lb tensile-strength mil-spec cable, the OM-2 is the workhorse of the Batca Omega line. Gas-assisted seats, pop-pin adjustments, and contoured lumbar-supported pads mean a 5’2″ member and a 6’5″ member both set up in seconds and train comfortably.

The full-length weight stack enclosures keep the plates contained and the floor clean, which matters in a commercial setting where downtime and housekeeping cost money.

The Omega 2 is the right call for commercial gyms, multi-family fitness centers, hotel and corporate wellness facilities, and personal training studios that want one machine to cover a complete program. Add the optional leg press / seated calf raise to convert the OM-2 into a closed-chain lower-body station as well, with a walk-through frame and 2:1 weight ratio that lets lighter members train heavy without maxing out the stack.

Optional Leg Press / Calf Raise Add-On

The OM-2 Leg Press turns the Omega 2 into a complete lower-body training station. Walk-through frame design gives easy entry and exit, the easy-access weight stack is reachable without contortion, and the four-bar linkage produces a smooth arc that feels natural through the full range.

The extra-large footplate handles a wide stance, lumbar support keeps the spine neutral, and the 2:1 cable ratio means a member can load the full stack to 200 lb and press 400 lbs of weight resistance at the leg press, which is the right resistance curve for most commercial users. Sold separately.

Two Users, One Machine, Zero Wait Time

Two independent 200-lb weight stacks run on chromed guide rods with rubber suspension bumpers. Motion stays smooth and the noise stays low across a full day of use. A member can finish a chest press set on one side while another member runs leg curls on the other side, with the cable paths never crossing and the counter-balanced press arms staying predictable under load.

Commercial-Grade Construction

Frames are bent with an inside mandrel and MIG welded, then abrasive blasted, chemically treated, and electrostatically powder coated for adhesion that holds up to repeated wipe-downs.

The 2″ × 4″ and 1-1/2″ × 3″ 11-gauge steel tube backbone is overbuilt for the rated loads, and rubber-foot mounting plates protect the floor and keep the machine from walking during heavy pulls. Sealed bearings and oil-impregnated bronze bushings operate on solid shafts, so the pivot points stay tight long after the warranty ends.

Adjustability for Any Member

Gas-assisted seat adjustments, telescoping pad adjustments with nylon sleeves, and laser-cut cams with starting-point adjustment let the OM-2 fit members from 5’2″ to 6’5″ without compromise. Handgrips are ergonomically molded and non-absorbing, which matters in a facility where members are sweating through sets back-to-back.

Cable System That Holds Up

The nylon-coated, lubricated mil-spec cable is rated to 2,000 lb tensile strength and runs on glass-reinforced nylon pulleys with precision steel ball bearings. Cable ends pivot on oil-impregnated bronze bushings, which is the spec you want when a machine is going to see ten-plus sets an hour in a busy commercial setting.

Exercises You Can Perform

• Chest Press
• Lat Pull-Down / Swiveling High Pulley
• Ab Crunch / Mid Pulley
• Leg Extension
• Seated Leg Curl
• Chest-Supported Mid Row
• Cable Shoulder Press
• Pec Fly
• Bicep Curl
• Inner / Outer Thigh
• Glute Kick
• Upright Row
• Shoulder Shrug
• Leg Press (with optional LP add-on)

Key Features

• Two independent 200-lb weight stacks for simultaneous two-user training
• Single-station frame design keeps motion paths consistent
• Gas-assisted seats with pop-pin adjustments for fast member turnover
• Counter-balanced press arms with starting-point adjustment
• Nylon-coated, lubricated mil-spec cable rated to 2,000 lb tensile strength
• Glass-reinforced nylon pulleys on precision steel ball bearings
• Sealed bearings and oil-impregnated bronze bushings at every pivot
• Full-length weight stack shields for safety and a clean floor
• Contoured lumbar-supported pads, double-stitched upholstery
• 11-gauge structural steel frame, electrostatically powder coated

Specifications

• SKU: OM-2
• Frame: 2″ × 4″ and 1-1/2″ × 3″ 11-gauge structural steel tube
• Weight Stacks: Two × 200 lb (400 lb total)
• Cable: Nylon-coated mil-spec, 2,000 lb tensile strength
• Dimensions (Base Unit): 7’5″ L × 6’3″ W × 7’0″ H
• Dimensions (With Leg Press): 7’5″ L × 8’6″ W × 7’0″ H
• Product Weight (Base Unit): 1,075 lb
• Product Weight (With Leg Press): 1,320 lb
• Finish: Electrostatic powder coat

Footprint

Omega 2 Base Unit Footprint

Omega 2 with Leg Press Footprint

Commercial Warranty

• Frame: Lifetime
• Moving Parts: 10 Years
• Cables, Belts, Other Parts: 5 Years
• Upholstery & Paint: 1 Year

(Warranty terms reflect standard Batca commercial coverage. Final warranty supplied with the unit at delivery.)

Ideal For

• Commercial gyms and health clubs
• Multi-family and apartment fitness centers
• Hotel and corporate wellness facilities
• Personal training studios
• School and university strength rooms
• Physical therapy and rehabilitation clinics
• Home gyms seeking commercial-grade quality

Customers Also Viewed:

• Batca LINK LFT Free Trainer
• Precor Small Cardio Equipment & Multi-Gym Package
• Precor S3.45 Multi-Gym
• HOIST 2-Stack Multi-Gym (H-2200)
• Life Fitness Signature Bicep Curl

Specifications